Electric Actuated Butterfly Valve FN/F series

Production Data

Body

FC300 (for F series only)

FCD450

Disc

					D: FCD450 (CNi PLTD) . U: SCS14
					A: ALBC3 . F: PTFE (for F series)

Seat

					E: EPDM . B: NBR
					T: PTFE (for F series only) N: CR (for F series only) V: FKM (for F series only)

Stem Seal

Depend on seat material

Valve Type		Actuator					H			L		Cv
FN/F		AE1- AE2-	AEX-	AD1- AD2-	HD1- HD2-	PDX- PHX- PHR-	AE1 AE2 AEX	AD* HD*	PDX PHX PHR	FN type	F type
Valve DN	Sizing code	AE1- AE2-	AEX-	AD1- AD2-	HD1- HD2-	PDX- PHX- PHR-	AE1 AE2 AEX	AD* HD*	PDX PHX PHR	FN type	F type
50A	0	300	360	300	300	300	273	332	332	41	41	159
65A	0	300	360	300	300	300	290	349	349	44	44	266
80A	1	.	.	300	300	.	.	356	.	44	44	457
80A	0	600	700	700	700	700	313	356	356	44	44	457
100A	0	600	700	700	700	700	346	384	384	51	51	860
125A	1	.	.	700	700		.	384	.	54	54	1320
125A	0	02K	02K	.	02K	02K	399	406	406	54	54	1320
150A	0	02K	02K	.	02K	02K	412	419	419	54	54	2020
200A	1	02K	02K	.	02K	02K	453	460	460	60	64	3540
200A	0	06K	06K	.	06K	06K	513	501	501	60	64	3540
250A	0	06K	06K	.	06K	06K	545	533	533	.	64	5580
300A	1	06K	06K	.	06K	06K	583	571	571	.	76	8080

NOTE:

*H: Heat isolation spacer is needed for low temp fluid less than -20°C.Please consult us.
Sizing code 1 can be used for clean fluid.

EPDM seat cannot be used for oil.
The temperature for water must be up to 80°C. Steam cannot be used.

Inherent flow characteristic		Outside Drawing

Seat material and temperature rating

Seat material	Temperature rating	Application
EPDM (Ethylene propylene rubber)	-20 to 80°C	for water
NBR (Nitrile rubber)	-10 to 60°C	for oil, air, slurry
PTFE (Teflon)	-40 to 80°C	for acid, alkali, corrosive fluid
CR (Chloroprene rubber)	-10 to 90°C	for weather resistance, chemical resistance
FKM (Fluorine rubber)	-5 to 80°C	for high temp. fluid, chemical resistance

NOTE:
Temperature rating is different depending on fluid characteristic. Please consult us.

EPDM seat cannot be used for oil.

The temperature for water must be up to 80°C. Steam cannot be used.

Sizing code 1 can be used for clean fluid

Thermal insulation is needed for low temp. fluid below -20°C. Please consult us.

Product Code

FN CORD

Actuator	Power Supply	High-power		Note	Control	Voltage
	AC	AE1	AD1	Standard ON-OFF type	AEX	1: AC100/110V
		AE2	AD2	Built-in relay	PDX	2: 200/220V
		HD1		High speed operation	PHX
		HD2		Built-in relay	PHR-
	DC	AD2/HD2		DC power supply type		0: DC24V

Option
L*:	Auxiliary signal limit switch
Other: See the actuator specs

		Light weight, low price and economical valve. Various seat and disc materials are available.

		Connection		J10K/ J5K(for FN series only) flanged, Wafer type
		Material		Various
		Valve DN		50 to 300A
		Maximum Pressure in MPa		1.0
		Fluids		Water, Gas, Oil (EPDM seat is not acceptable), Slurry, Vacuum 1 torr, Sea water (ALBC3)